PORSCHE 356 A CAR CARE KITCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1994-98 - Fuel/Exhaust (includes uncategorized and accessory items)
$1.83
Make a selection FVD559212 Includes the later model (series ii from 996) water cooled crest, gasket and emblem securing nuts. Size: 67 mm x 51 mm sold individually. 1 is necessary per car.
$214.78
Make a selection FVD559211 Includes the early model (series i) air cooled crest, gasket and emblem securing nuts. Size: 67 mm x 51 mm sold individually. 1 is necessary per car.
$225.23
Make a selection
$13.75
Make a selection
$55.00
Make a selection
$4.13
Make a selection
$15.95
Make a selection
$182.07
Make a selection
$13.75
Make a selection
$9.90
Make a selection
$47.30
Make a selection
$82.50
Make a selection BES99300100SK + 25 crank hp & + 20 crank torque. General Fitment911 1994-98
$10,891.34
Make a selection BBI9964010002 Finally, a complete solution to properly widen the front track width of a Porsche 996 and 997 turbo. To help increase front end grip, this kit allows full negative camber adjustment without binding the axles and fitment of wider wheel/tire combinations and GT3 cup car fenders. Each kit includes lower control arms, thrust arms, axle spacers, upper mounts, and camber shims.
$3,695.00
Make a selection BES99300241S The ultimate stainless steel system for the street. Completely civilized while cruising and opens at higher rpms. Quieter than the street / clubsport versions. More low and mid-range torque. Larger primaries, larger collector, largest diameter tubing on the market. Made for mid-range and top end performance with the added beauty of 3.5" (90mm) dual exhaust tips! + 25 crank hp & +24 crank torque (on average). - 2.9 tubing (75 mm) at the widest point. Primaries are 2.5" (64mm). - 200 cell hjs "hf" trimetallic catalytic converters. - t 316 lightweight stainless steel for improved durability over t 304. - 3.5" (90 mm) dual oval, double walled polished tips included. - intoxicating growl at idle, partial thrott...(choose a part on the right to read more) General Fitment911 1994-98
From $10,723.61
Make a selection 915300911550 If you are looking for a transmission oil cooler system that is simple to install, provides lasting results and is perfect for a driver, the weekender, or for track use look no further. This kit includes a sleek high-performance oil cooler that mounts simply to the transmission cover with the included bracket and hardware. The stainless braided lines seamlessly screw into the transmission housing drain / fill plug location, no modification required. The electric, self-priming, 12 v oil pump is made with helical bronze gears, a stainless-steel shaft and a nickel plated brass body for the reliability that you expect from your Porsche. The pump includes a bracket that allows for simple installation. Simply connect...(choose a part on the right to read more)
$1,529.00
Make a selection 99651290300G2X Rear spoiler only. The carerra aerokit underlines the performance potential and racing origins of the 911 coupe and cabriolet. Includes an aerodynamic nose section with integrated front spoiler, side skirts, GT rear side trim panels and a discreet, fixed rear spoiler with an integrated third brake light. Prices do not include painting and installation.
$7,431.08
Make a selection 220110981001 FVD Brombacherhas a long tradition of offering high quality, extensively tested, easily installed tuning products that offer proven performance. Those high standards naturally led us to the innovative pro design (ipd) plenum product. The ipd patented cast aluminum intake plenum with the larger 82 mm (gt3) throttle body (competition plenum) increases horsepower and torque by optimizing and increasing airflow into the intake manifold. But in order to capitalize on all the performance gains the ipd competition plenum can deliver, you must strike a balance with exhaust components and software. You cannot simply add the ipd competition plenum on the 981 series and expect large gains. But, no need to worry, the FVD ...(choose a part on the right to read more)
$1,479.50
Make a selection BBI9964010006 Finally, a solution that allows you to safely increase without the risk of damaging your front axles. as you add GT3 shims to your front Porsche 996/997 turbo lower control arms, you move the cv joints beyond their safe range of motion, risking failure and expensive damage. These 10mm thick precision spacers, used with 16mm of lca shims will provide an additional -1.7 deg. Of camber, while maintaining the factory cv joint and axle relationship. the spacer design features a concentric lip that positively and accurately locates it to the cv joint for perfect balance and no vibration. Each kit includes two spacers and all the needed hardware in high class 10.9 grad
$375.00
Make a selection 21011196402 Say good bye to the days of having to weld and cut aftermarket sport cats to make them fit! We have our sport cats made in Germany to our specifications and that means that these are 100% bolt on without issue! - + 10 crank hp & +6 crank torque. - 200 cell, tri metallic German hjs sport catalysts. - large volume o 105 mm (4.1 inch diameter) high flow cat. - exhaust hanger brackets are included so that the heat shield does not have to be removed. - weighs 7.2 lbs. (3,2 kg). - direct bolt on replacement. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - reduces backpressure and thermal stress. - made in Germany. - more distinguished flat 6 growl at wide open throttle. The FVD 200 cell...(choose a part on the right to read more)
$1,593.90
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |